Kitchen appliances usually have error codes that can help diagnose problems with the device. Although the code’s meaning may vary slightly depending on the model, they generally indicate similar issues. Even ovens, whether gas or electric, have error codes that can be triggered by various factors. If you encounter one of these codes, let’s figure out how to resolve it.
If your oven displays the F2 error code and beeps, it means that the temperature inside the oven has gone beyond the set limit. This issue can arise due to various reasons such as damaged elements, faulty sensors, damaged wires or a malfunctioning control board. To fix this problem, it is recommended to replace the oven’s control board or sensors. However, if you lack experience in this area, it is best to seek help from a specialist.
If your oven displays the F2 error code and beeps, you may be able to locate replacement parts by conducting an online search or reaching out to customer service for assistance.
Below is a compilation of error codes for various popular brands and models, as the meaning of the code may differ based on the brand and model. Simply scroll down to locate your brand in the list provided.
Caution: Prior to troubleshooting your oven, ensure that it is disconnected from the wall socket. It is recommended to seek assistance from customer support before making any modifications to your appliance. In case your appliance is still under warranty, dismantling parts may result in voiding the warranty.
Throughout this article, we will discuss sensors, control boards, heating elements, and wires, which may be located differently depending on the oven. Nonetheless, to provide a general idea of where to begin your search for these components, I have compiled a brief list below indicating their typical placement.
Temperature sensors are typically located at the back of the oven cavity and can be identified as thin metal cylinders in the upper left and right corners, usually attached to the back of the oven cavity with screws.
The heating elements are located inside the oven’s compartment and consist of a coiled metal rod situated at the top of the oven.
Control board: To locate the control board, you need to remove the back panels of the oven. Typically, an oven has two panels – a small one at the top and a larger one below it. After removing both panels, you will find the control board where all wires are connected. If you plan to remove it, make sure to take a picture beforehand to remember how to reassemble it correctly without any help.
Wires are located inside the oven, and to access them and their connections, it is necessary to remove the back panel or panels of the oven.
If your Whirlpool Oven displays the F2 error code, it indicates that the temperature measured by the control board and sensors is too high, which may or may not reflect the actual temperature inside the oven.
If any of these components are defective, the displayed readings will be inaccurate. Loose wires or a malfunctioning door lock mechanism in self-cleaning ovens can also be responsible for this issue.
Control boards or sensors that are not functioning properly can inaccurately regulate temperature and should not be relied upon.
What To Do When Your Whirlpool Oven Says F2
Although it is advisable to entrust most repairs to skilled experts, there are a few tasks that you can undertake independently. Commencing with troubleshooting is a wise decision. However, if you lack expertise, I suggest leaving the subsequent steps to someone more knowledgeable in this area. Nonetheless, here’s what you can attempt.
For self-cleaning models: Check the door lock mechanism for any signs of physical damage and ensure that there is nothing obstructing it from locking.
Inspect the bake and broil relays to ensure that all wires are correctly connected, and if there is any visible damage, you may need to replace the control board. If you choose to re-connect loose wires by yourself, be cautious while handling the control board and make sure you know what you’re doing.
Inspect the wires for any indications of physical harm to guarantee their proper functioning.
Ensure that the sensors, sensor harness, and connections are functioning correctly and appropriately linked to the control board. Additionally, verify that the resistance in the sensor circuit is within the operational range.
GE Oven F2 Error Code
When a GE oven shows the F2 error code, it indicates that the temperature has exceeded the predetermined limit for the device, which is typically set to prevent unsafe temperatures. This may be due to faulty sensors or a damaged control board.
What To Do When Your GE Oven Says F2
To resolve the issue of F2 error and beeping in the oven, it is necessary to diagnose the temperature sensors which are metallic rods that exhibit different levels of resistance based on the temperature, with higher resistance indicating a higher temperature reading by the control board.
Start by unplugging the oven range and plugging it back in after a 5-minute interval. If resetting the oven resolves the F2 error code and you can use it without encountering the same issue, then you’re all set. Nevertheless, resetting the oven is probably just a short-term solution, so I suggest investigating further to identify and address the underlying problem.
Using an ohmmeter, check if the resistance measured by the sensors falls within the expected range of 1080-1090 ohms by unplugging them from the oven and inserting the meter into their plug receptacles; if the reading exceeds this range, it indicates faulty sensors that require replacement.
Inspect the wires for any indications of physical harm to ensure their integrity.
Assuming the sensors are functioning properly, it is probable that the control board is malfunctioning due to high temperature or a short circuit, and replacing it is advised as repairing it can be challenging.
When the temperature measured by a Kenmore Oven’s sensors is too high, it will indicate an F2 error code, which usually indicates that the oven is experiencing difficulty in regulating temperature due to faulty control board or sensors.
Nonetheless, an overheating oven can also result from a faulty heating element, which may continue to operate even when the oven has reached the desired temperature due to being burnt.
What To Do When Your Kenmore Oven Says F2
To check if the sensor probe is working correctly, take it out of the oven and use an ohmmeter to test its resistance. If it measures around 1100 ohms, then it’s okay to proceed with further troubleshooting. However, if the reading is different, then you should replace the sensor probe.
Inspect the heating element for any visible indications of harm, and detach it before examining it with an ohm meter to determine if it is shorted to the ground.
Inspect the control board for any signs of loose connections or damaged wires.
JennAir Oven F2 Error Code
If your Jenn Air Oven shows the F2 error code, it means that the temperature inside the oven has gone beyond the safe limit, which could be due to a defective sensor, damaged wires, a malfunctioning heating element, or a faulty relay board.
What To Do When Your Jenn Air Oven Says F2
Locating the sensors in your oven and tracing the wires that connect them to the control board, then measuring their resistance with an ohm meter should yield a reading of approximately 1050-1100 ohms; if they are not functioning correctly, it is recommended that you replace either the sensors or the control board.
Inspect the broiler and bake elements to ensure they are functioning properly as a faulty or broken heating element may dispense excessive heat and continue operating when it should be turned off.
Inspect the relay board for any physical damage to either the board or the wires connecting to it. Keep in mind that even if there are no visible signs of damage, the control board may still be defective. If all other components appear to be functioning properly, it is recommended to replace the control board.
If the door of your HotPoint Oven is unlocked and the temperature inside exceeds 590 degrees Fahrenheit, it will display the F2 error code. This error code can indicate issues with malfunctioning sensors, damaged wires or heating elements, or a faulty control board.
What To Do When Your HotPoint Oven Says F2
Locate the oven sensors and trace their wires to the control board, then use an ohm meter to measure their resistance, which should be around 1050-1100 ohms.
Inspect the broiler and bake elements to ensure they are functioning properly as a faulty or broken heating element may dispense excessive heat and continue operating when it should be turned off.
Inspect the relay board for any physical damage to either the board or the wires connecting to it. Keep in mind that even if there are no visible signs of damage, the control board may still be defective. If all other components appear to be functioning properly, it is recommended to replace the control board.
LG Oven F2 Error Code
When an LG oven shows the F2 error code, it means that there is a problem with the temperature sensor, which could be due to damaged wires or a short-circuit. The best way to fix this issue is by replacing the sensors. However, depending on the model of your oven, this error may also indicate a problem with the door locking mechanism.
What To Do When Your LG Oven Says F2
To fix the F2 error on your oven, you need to find the metal sensors located at the back of the oven’s cavity, which are thin 2-3 inch metal cylinders that can be unscrewed and removed. You can purchase new parts online or seek assistance from customer support for replacement options, but it is advisable to consult a technician if you lack confidence in your repair skills.
You can also check this video about “What To Do If Your Oven Says F2 (& Beeps)”
